Foster Requested By Steven R. Therefore, presented herein are the mechanical and metallurgical test data for. Tensile strength averaged , psi MPa vs. Shear strength averaged , psi MPa vs. Fatigue life successfully achieved , cycles discontinue vs.
|Published (Last):||22 September 2008|
|PDF File Size:||14.39 Mb|
|ePub File Size:||11.63 Mb|
|Price:||Free* [*Free Regsitration Required]|
Edition : P5. Date: Dec. STAGE :. Aerospace series Bolt — Protruding head, Short thread Inch series. Superseding Ref. Master document :.
DocMaster: Uncontrolled copy when printed This product standard specifies the dimensions, tolerances and the requirements of a protruding head bolt for aerospace application. This European Standard incorporates by dated or undated reference, provisions from other publications.
These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision.
For undated references the latest edition of the publication referred to applies including amendments. Titanium alloys bars, wire, forgings, and rings 6AL-4V annealed. Titanium alloys bars, wire, forgings, and rings 6. Alloy bars, forgings and rings, corrosion and heat resistant. Steel bars, forgings, and rings.
Steel bars and forgings. Steel bars 0. Steel bars, forgings, and rings, 0. Steel bars, forgings, and tubing 0. Normalized and tempered. Heat treatment of steel, raw materials. Plating, cadmium electrodeposited. Surface texture surface roughness waviness, and lay. Aerospace — UNJ threads - General requirements and limit dimensions. Aerospace series — Marking of aerospace products.
Aerospace series — Aluminium pigmented coatings — Technical specification. Aerospace series - Threaded bolts, light weight - Inch series - Technical specification. Specification for lubrication of bolts with cetyl alcohol.
Process specification — Aluminium base protection for fasteners. Aerospace — Anodic treatment of titanium and titanium alloys - Sulfuric acid process. Configuration, dimensions and tolerances shall be in accordance with figure 1, tables 3 and 4. Dimensions and tolerances for oversizes shall be in accordance with table 5.
Limitation of application: large diameter to titanium fasteners are not recommended for single shear applications, use ABS instead; diameter titanium fasteners are not recommended for single shear applications at all.
The calculation of the mass of a bolt shall be provided as per indications hereafter :. Add the mass of the head and threaded part invariable mass to the mass of the smooth part variable mass. Total mass of the head and threaded part :.
Mass of the smooth part :. Multiply the value of the 2nd mass column of table 3 value according to the diameter code No. Invariable mass. Variable mass. Total mass. Table 1: Materials, finishes, lubrication and identifications. Sulfuric-acid anodizing as per ISO IVD as per EN Titanium alloy 6AL-4V.
Aluminium coating as per specification. Cetyl alcohol. Rc min. A blue paint. Table 2: Mechanical characteristics. Thread of steel bolts shall be carried out after heat treatment. Figure 1: Configuration, dimensions and tolerances. Note 1: For nominal diameter: The diameter measured at point I shall be less than or equal to the max.
For oversizes diameters: Maximum diameter at point I shall be incremented by. The TD diameter stays the same as for nominal diameter. Note Check concentricity of diameters D shank and TD thread to avoid interference between the bolt. The maximum thread runout and functionality for first and second oversizes is incremented by 0,25 mm,.
Only for B coded fasteners, threads shall be coated with aluminium coating as per EN Only for B coded fasteners, Overspray of EN is permissible in this area. Dimensions in millimeter. Table 3: Dimensions, tolerances and mass. Dimensions in millimeter continued. Thread a. T or B code. Table 3: Dimensions, tolerances and mass Dimensions in millimeter continued. Hexagonal recess.
Table 3: Dimensions, tolerances and mass concluded. MASS Ref. Head and thread. Smooth part. St eel. Thread as per AS except diameter TD. Table 4: Dimensions and tolerances.
Table 4: Dimensions and tolerances concluded. Dimensions in millimete r. Learn more about Scribd Membership Home. Much more than documents. Discover everything Scribd has to offer, including books and audiobooks from major publishers.
Start Free Trial Cancel anytime. Uploaded by mtcengineering. Document Information click to expand document information Date uploaded Nov 13, Did you find this document useful? Is this content inappropriate? Report this Document. Flag for Inappropriate Content. Download Now. Related titles. Carousel Previous Carousel Next. Jump to Page. Search inside document. Page 7. See detail A. G max.
Chamfer S. Thread runout max. Thread functionality 1,0 pitch. Coating mandatory see note 4A.
Stocking Distributor of EN6115 & EN6114 Fasteners
Please enter the email address associated with your account to recover your username. Please enter the username associated with your account to recover your password. The email address you provided matches multiple accounts. Please contact your Boeing Distribution Sales Representative for further assistance. Your request has been submitted. Please check your email for login instructions it may take up to 24 hours. If you have not received an email, Please email ecomsupport boeingdistribution.
EN6115-P5 (Aerospace Series, Bolts).pdf
Thank you for interesting in our services. We are a non-profit group that run this website to share documents. We need your help to maintenance this website. Please help us to share our service with your friends. Share Embed Donate. These normative references are cited at the appropriate places in the text and the publications are listed hereafter.
EN6115-P5 (Aerospace Series, Bolts).pdf
Please enter the email address associated with your account to recover your username. Please enter the username associated with your account to recover your password. The email address you provided matches multiple accounts. Please contact your Boeing Distribution Sales Representative for further assistance. Your request has been submitted.